Limited version of the replica with the TITAN ™ V2 Advanced system by GATE!

The TITAN ™ V2 Drop-In mosfet controller set transforms the AEG into an advanced training replica. Thanks to it, you will gain a tactical advantage, thanks to the rapid response to the trigger, with the possibility of modifying the replica and adapting it to each mission with 20 available functions. This is the most advanced and top model from GATE.

The TITAN ™ V2 controller will breathe a completely new life into an ASG electric replica.

TITAN ™ gives you new possibilities:

• - Trigger sensitivity adjustment
• - Pre-cocking boost, i.e. spring tension control (shortens the time from pressing the trigger to the shot)
• - Adjusting the fire selector modes
• - Burst shot mode
• - Rate of fire adjustment
• - Alerts you when the battery is low
• - Protects the battery from damage
• - "Sniper Delay"
• - Full cycle detection
• - AUG mode - the ability to set two trigger sensitivity (single and continuous fire)

The SA-B16 assault rifle replica by Specna Arms is made largely of a uniform zinc and aluminum alloy, with the use of steel elements in the most vulnerable points of the replica (steel elements - all the screws, pins and tactical sling swivels). The stock holding the battery and the pistol grip were made of polymer plastic. The replica's body and the RIS rail set have been anodized, which guarantees a high degree of protection against corrosion. The painting of the replica itself was made by powdering, after the surface was sandblasted. This ensures a much higher than usual abrasion resistance of the applied paint. There are Specna Arms markings on the body.
The replica fits very well - in a way that has been observed almost exclusively by G&P or Classic Army manufacturers - and perfectly balanced. This ensures almost perfect maneuverability of the replica, and its weight is almost imperceptible after placing the replica on the shoulder.

The replica uses a new generation quick spring change system, the so-called SAEC ™. This allows for quick and efficient adjustment of the replica's power to the conditions expected in the game field without the need to have access to a workshop or a number of specialized tools. The spring replacement process is now even faster than in the previous version of the system.

Thanks to the SAEC ™ System, there is no need to take the gearbox out of the replica - you just need to disassemble the stock and then unscrew the special pin underneath it with the spring guide. Replace the main spring, screw the pin back into the body, attach the stock, then ... back to the game! The entire operation requires only a long Phillips screwdriver to unscrew the stock.
The advantages of the SAEC ™ System are difficult to overestimate. In the light of the tendency prevailing throughout Europe to apply legal limits of the muzzle velocity of the replica and the arrangements existing within the environments themselves, this system guarantees the user considerable possibilities and a lot of freedom. The SAEC ™ System allows you to replace the main spring with a minimum of time, and thus adjust the muzzle velocity of the replica to the area of ​​the game so as to guarantee an ideal compromise between the effectiveness of fire and the safety of your own and other players.

The replica has been fully adapted to work with LiPo and LiFe batteries. Thanks to the basic muzzle velocity of ~ 430 FPS guaranteed by the factory-installed main spring, the replica is perfect for middle-range operations.

The gearbox, reinforced at the height of the cylinder head, hides a steel spring guide, which is an element of the SAEC ™ System, and steel gears mounted on 8-mm ball bearings and washers. The system is secured by means of four anti-reversal latches. A light, made of polycarbonate plastic piston is equipped with a set of steel teeth to increase its durability. A type 2 cylinder and a steel interrupter were also used here, as well as a metal hop-up chamber.

The Upgraded version has a number of new, enhanced parts such as

• - a set of reinforced steel gears
• - steel spring guide with ball bearings
• - light, polymer piston with a steel strip
• - aluminum, sealed piston head
• - metal cylinder head
• - sealed metal nozzle

The replica is equipped with a top 22 mm RIS rail and a set of front RIS rails in the Free-Float system. Metal flip-up sights are mounted on the upper RIS rail, but they can be easily replaced by any optoelectronic sights. The muzzle device is seated on a 14 mm left-hand thread, which allows the attachment of a silencer in its place.

To increase the realism of the game, the replica was also equipped with a working bolt release device.

The kit includes

• - replica with the TITAN ™ V2 system installed
• - USB connector for controlling the unit with the GATE Control Station application
• - magazine
• - mechanical sights
• - ramrod
• - additional main spring

The set with the replica also includes a steel hi-cap magazine with a capacity of 300 BBs.

The set does not include a battery and a charger.