The TITAN™ V3 Drop-In mosfet controller kit transforms your AEG into an advanced training replica. It gives you a tactical advantage with its lightning-fast trigger response, with the ability to modify the replica and adapt it to any mission with 20 available features. This is GATE's most advanced and top of the line model.
The TITAN™ V3 controller breathes a whole new life into your ASG electric replica.
The TITAN chip in the ADVANCED version has unlocked access to all programming functions using the GATE Control Station.
TITAN™ gives you new possibilities:
- - Trigger sensitivity adjustment
- - Pre-cocking boost, i.e. regulation of keeping the spring tensioned (shortens the time from pressing the trigger to firing)
- - Adjustment of fire selector modes
- - Batch firing mode
- - Rapid rate of fire adjustment
- - Warns of low battery level
- - Protects the battery from damage
- - "Sniper delay"
- - Full cycle detection
- - AUG mode - possibility to set two trigger sensitivities (single and continuous fire)
A broader description of the TITAN™ controller functions:
TRIGGER SENSITIVITY ADJUSTMENT
Five sensors allow to control the trigger sensitivity. There is no need to disassemble the replica, just use the Tactical Programmer Card or the GATE™ Control Station application. It will allow you to adjust the replica to your skills and individual preferences.
CONFIGURABLE FIRE SELECTOR (gen. 2)
The two sensors can be programmed in three ways, with up to 6 functions to choose from.
- - SAFE-SEMI-AUTO
- - SAFE-SEMI-SEMI
- - SAFE-SEMI-BURST*
- - SAFE-BURST*-AUTO
- - SAFE-SEMI-BURST*/AUTO (short press on BURST, long press on AUTO trigger)
- - SAFE-BURST*-AUTO (SAFE by quickly switching modes, then: SAFE-SEMI-SAFE)
*BURST means series firing mode.
CYCLE DETECTION
The TITAN™ control unit can accurately detect the position at which it should end the cycle. Thanks to this, even the shortest squeeze of the trigger will result in a full cycle (replicas without the TITAN™ system often stutter when the trigger is held too short, if it does not end in a shot. TITAN™ eliminates this defect).
This gives you:
- Automatic BURST (batch) mode, there is no need to set the batch cycle time, just set how many rounds are to be fired
- Automatic Pre-Cocking, which is available in every fire selector setting mode: SEMI BURST and AUTO. So, unlike conventional MOSFETs, you don't have to configure this function manually. All you need to do is set the spring pre-pull power
- ALWAYS FULL CYCLE PERFORMED - when pre-cocking is turned off, TITAN™ will make sure that the gearbox will perform a full cycle and the spring will definitely be released after firing. This results in greater reliability of the gearbox.
PRE-COCKING (gen.2*)
Since victory in a duel often depends on a fraction of a second, thanks to the pre-cocking of the spring we achieve a response to the trigger comparable to a real firearm. The spring is pre-tensioned, so at the same time we warn that using this mode on strong springs leads to faster wear of internal parts of the replica.
There are two modes of using the PRE-COCKING function:
1. AUTO (-matic) mode - the spring is tensioned after each shot
2. SMART mode - the spring is tensioned by slow pressing the trigger, and the shot is fired by quick pressing it.
Three PRE-COCKING mode options can be programmed: HIGH / MID / LOW - each will adjust the spring tension to a different degree
*The PRE-COCKING mode now works in all selector modes: SEMI, BURST, AUTO and does not require manual calibration
BURST (gen.2)
BURST mode, or programmable batch shooting, now only requires selection of the number of pellets to be fired (up to 10 pellets / trigger pull). This is very useful on any MILSIM or when using real/low -cap type magazine
s.
ROF CONTROL
Allows to reduce the rate of fire of the replica. Thanks to this you can use stronger Li-Po batteries and still have the firing rate consistent with the real weapon.
ROF STAB
Allows you to change the way ROF CONTROL works:.
- ON - ROF Control regulates the speed of the cycle, making the Gearbox run smoothly and reducing wear on the replica's internal parts
- OFF - RIF Control adds pauses between each shot to reduce the rate of fire. This gives a very realistic feeling
SNIPER DELAY
Allows you to set the delay between each shot in SEMI mode to simulate the delay by reloading or recoil compensation. Can be set to: 0.5s, 1.0s, 2.0s, 3.0s
For a comprehensive description of all functions, please visit the manufacturer's website: http://www.gatee.eu/
Full instructions can be found at the following address:
https://gatee.eu/pl/produkty/titan/titan-v3-pl
The kit includes:
- - TITAN V3 module with ADVANCED firmware version
- - USB-Link
- - Installation kit
- - MICRO-USB cable
- - USB-C cable
- - Quick start guide
- - TITAN badge